WWW-POSIM v0.6.16Simulator documentation
Documentation menu
WWW-POSIM / Simulator documentation

Feature demonstrations

Watch terrain preparation, missions and sensor inspection in the workspace. Each clip records actual interaction with that feature.

Video overview

YouTube recordings retain their recorded version and preview scope. The feature-specific clips below remain available.

Browse the video playlist

Feature overview — 0.6.5 recordings and development previews

Workspace, vehicles, sensors and control, with labelled PR #88 sonar and experimental SLAM segments.

Watch on YouTube

Set starting latitude / longitude

Set terrain coordinates and the robot starting location independently.

Watch on YouTube

  1. Set the region coordinates in Workspace.
  2. Choose a prepared world and a robot profile.
  3. Set the robot latitude / longitude and surface spawn.

Waypoints

Plan a route, run an Autopilot mission, hold and return to the start.

Watch on YouTube

  1. Add waypoints on the map; right-click a point to remove it.
  2. Check the route on the terrain, then select Run route.
  3. Stop holds position; Continue resumes. Abort cancels and disarms.

Simulation speed

Select a target speed and check the measured simulation rate.

Watch on YouTube

  1. Disarm and finish any active mission before changing speed.
  2. Select 0.25×, 0.5×, 1×, 2× or 4×. Actual speed depends on CPU / GPU and sensor load.
  3. Live AIS is hidden above 1×. Restore 1× before enabling it again.

Realtime AIS-synced ships

Enable the available AIS source and inspect nearby vessel reports. Coverage varies by location.

Watch on YouTube

  1. Run at 1× and enable Marine traffic in Scene.
  2. Live messages supply vessel type, identity and available size data; coverage and reporting delays vary.
  3. Reported ships are visual-only, with no collision; faster simulation removes them.

Robot studio

Build a vehicle, configure its sensors and save an immutable revision.

Watch on YouTube

  1. Open Custom robots and choose WAM-V or BlueROV2 in the vehicle builder.
  2. Choose sensors, inspect their settings and select Generate & Save.
  3. Find the result in Saved vehicles. Edit a copy preserves the original configuration; export its ZIP to keep a portable copy.

Custom Autopilot parameters

Upload, edit and read back supported FCU parameters while disarmed.

Watch on YouTube

  1. Open ArduPilot parameters while disarmed.
  2. Upload a parameter file or edit a supported value.
  3. Apply and verify the native FCU readback; protected safety parameters remain restricted.

ROS2 topics

Search topics, subscribe, inspect values and draw supported world-frame poses.

Watch on YouTube

  1. Search topics and inspect numeric plots, raw values or supported world-frame poses.
  2. Desktop RViz2 receives telemetry through the authenticated relay; the HTTPS connector carries it.
  3. Select ROS2 direct control in your world and connect your local code with www-posim-connect --control. The relay delivers native sensors and bounded robot commands.

Dive & inspect

Watch BlueROV2 descend toward its inspection depth.

Watch on YouTube

  1. Start with the underwater profile on the sea surface.
  2. Use the short inspection mission, then Vehicle to observe the descent and return.
  3. Compare robot depth, heading and native camera data.

Live sensors

Select a native Gazebo camera and enlarge its live image.

Watch on YouTube

  1. Open Sensors and select a sensor from the tree.
  2. Camera streams support the configured 1, 2 and 5 Hz rates.
  3. Use numeric plots or raw values for supported non-image sensors.

Ground control

A collapsible map combines geographic planning and mission controls.

Watch on YouTube

  1. Zoom, pan or locate the robot, and edit the route on the map.
  2. Arm/disarm, Stop, Continue and Abort remain available during an owned session.
  3. The full-screen Focus view retains the minimap and essential status.

Workspace basics

Workflow recordings

Multi-vehicle demonstrations — development preview

Fleet setup, independent missions and cancellation, and a same-run acoustic report for two LRAUVs. Surface and underwater observations are separate recordings. The aerial vehicle takes off from shore, approaches the surface vessel and returns to shore. Reports from cancelled runs are offline results.

Watch on YouTube

Getting started — 0.6.5

Prepared world, WAM-V, sea state and workspace panels. Recorded in a local fixture with the account gate disabled.

Watch on YouTube

Worlds, waves and currents — 0.6.5

Prepared Hong Kong terrain and environment settings. Settings and solver readback are demonstrated; a measured current-induced trajectory is not established.

Watch on YouTube

Build and reuse a vehicle — 0.6.5

Configure a WAM-V camera, save its revision and reuse the saved camera settings after a local runtime restart.

Watch on YouTube

Sensors, ROS 2 and RViz — 0.6.5

Camera, LiDAR, IMU, ROS 2 topics and native RViz in an isolated local fixture. Movement during the bounded Python command includes environmental effects.

Watch on YouTube

ROS 2 direct control — 0.6.5

A Python program commands the WAM-V forward for 25 seconds, followed by an operator stop. This is direct control; displacement includes environmental effects.

Watch on YouTube

Research previews

Physics-based sonar — PR #88 development preview

Recorded on Apple Metal with a 0.6.4 development build: a downward-tilted sonar fan, excluded surface echoes and display range gain. Range-and-bearing returns are not a 3D reconstruction.

Watch on YouTube

Visual-inertial SLAM — PR #88 development preview

An experimental 0.6.4 map from the same run as the downward camera, approximately aligned by simulation clock and slowed to 0.65×. The recording uses a fixed viewpoint and enlarged crop; the map is not navigation-ready.

Watch on YouTube

Search documentation